Thistle sailboat

Compass

Use to read the shifts. Non-racers can use for conventional navigation

Mounted compass assembly

- mount between stanchions just below forward grating

teak, Ritchie SS2000

GF691

$417.00

teak, Ritchie SS1000

GF692

$270.00

teak, Ritchie RU90

GF693

$182.00

mahogany, Ritchie SS2000

GF591

$407.00

mahogany, Ritchie SS1000

GF592

$260.00

mahogany, Ritchie RU90

GF593

$172.00

Compasses

Ritchie 2000, dial diameter 4 1/2"

GB833

$330.00

Ritchie 1000, dial diameter 3 3/4"

GB832

$198.00

Ritchie RU90, dial diameter 3"

GB830

$110.00

Compass mounts

- supply your own compass

teak, for Ritchie SS2000

GE691-1

$87.00

teak, for Ritchie RU90, SS1000

GE691

$72.00

mahogany, for Ritchie SS2000

GE591-1

$77.00

mahogany, for Ritchie RU90, SS1000

GE591

$62.00

Hazard course computer

- translate the compass readings into lift and header information

GB841

$15.00

Fiberglass

Bilge stiffener kit

- includes foam stiffener strips, bedding and covering fiberglass, requires polyester resin.Stiffen the bilges of your soft fg boat

GB820

$160.00

Stern tanks, pair

- includesbedding and covering fiberglass, requires polyester resin. Requires fitting. Add flotation tanks to yourearly fg hull

GE020

$160.00

Seat tanks, pair

- includes bedding and covering fiberglass, unmounted inspection ports, chain plates. Will require new cross- thwart. Replace old leaky, swayback seats in older fg hulls.

GE030

$725.00

Seat horn repair kit

- fixes the deformation of the forward face of seat tank on some fg hulls

GC720

$52.00

Flotation

1 to 2 lb styrofoam sticks to provide TCA-required positive flotation in fiberglass hulls

Sticks

- bundle of 25 pcs. Fills inside of tanks on fg hulls. 3 bundles needed for one boat.

GE845

$49.50

Shaped blocks

- hot-wire-shaped to fit wood hulls. For durability, will need coating or bagging

full set, includes packing for shipping

GA015

$635.00

full set

GA015-1

$565.00

bow

GE840

$215.00

seat, 4 pc

GE841

$175.50

forward pcs, set of 2

GE844

$108.35

aft pcs, set of 2

GE842

$67.25

stern, 2-piece set. Also fits older fg hulls without stern tanks

GE843

$174.00

Hull attachments

The pieces and parts that attach to exterior of the hull

Bailer - Anderson Elvstrom 'Super max'. Interior plate 3 x 5 1/4", hole through hull 2 1/8 x 4 11/32"

GB020

$149.00

Centerboard gasket

- two-piece, heavy-duty folded sailcloth

GB825

$34.00

Gudgeon, ea

- heavy-duty double-loop strap with 4 mounting holes. Fits 3/8" pintles

RL490

$13.25

Keel strip

- 1/2" wide aluminum half round

full set

GE820

$93.50

full set with fasteners

GC820

$69.50

stem - runs down stem and extends 8" aft of stem

GE821

$13.50

stem with fasteners

GE821-1

$14.10

forward - runs from stem piece to 2" fwd of CB trunk

GE822

$22.60

trunk - holds the CB gasket in place, pair

GE823

$38.10

aft - from CB trunk to transom

GE824

$19.50

5200 sealant

- use to seal keel-strip screws. Silicone does NOT work

GB771

$14.47

Lifting

Hoist your boat safely

Lifting bridle assembly

- 3/8" dacron. With 2 stainless S-hooks for attachment to forward grating and D-shackle for aft attachment. Grating hardware is included, aft hardware is not

GF820

$52.25

bridle only

GF821

$45.40

Lifting hardware

- for permanent attachment to theboat

forward grating hardware for lifting bridle

GF822

$11.25

aft lifting claw for GMW, late D&M

XE179

$16.25

4 hole eye strap for early D&M. Mounts to trunk angled aft cover

RL314B

$2.65

MIscellaneous

Inspection port

- 4", includes fasteners

GC855

$9.00

Closed-end aluminum pop rivets

use to install inspection ports, attachment of boom end castings

GB722

$0.30

Aluminum washer

use inside tank as pop-rivet backer when installing inspection ports

GB723

$0.05

Quick-release pin

- 3/16", solid hardened-stainless pin with ball detent at one end. Caution - the hollow, center-push quick pins will break under shroud loads

medium lenght, attaches shroud to chain plate on seat

GB005

$4.25

short length, attaches shroud to shroud extender or Staymaster

GB013

$3.95

Shroud plate bushings - needed if you're removing shroud plates for varnishing or replacing rails, pair

GB016

$3.75

Replacement pad

for spinnaker guy hook, pair

GB310

$3.75

Spinnaker pole

Complete pole

- 1 1/4" aluminum tubing, stainless steel and bronze end fittings, and eyestrap for topping lift attachment

GF130

$200.00

pole only with one end plugged

XF131

$52.00

pole end with fasteners, ea

RF677F

$58.75

Spinnaker pole-end repair parts

- pin plunger, spring, ring

RF677-1

$7.75

Trailering

Thistle trailer

- Wesco. Galvanized, low-to-the-ground, 5 support rollers

GF993

$2675.00

Trailer center bunk

- laminated, pressure-treated and padded. Curved to match contour of hull

GC994

$275.00

wood only

GB994

$185.00

Trailering mast support

- secures to aft grating

GE830

$30.00

Trailering tie-down strap

GB980

$17.70

Traveler

Traveler track and car

- includes end stops and fasteners. New boats use H2729 for car. Other choices below

GC330-1

$271.80

traveler track, includes end stops and fasteners

H2720-1

$87.05

end stops for traveler track

H173

$8.35

Traveler car

- all cars are captive-ball style, none fit the old-style track

with eye strap for mainsheet block and 2 sheaves for traveler control

H2729

$184.75

ti-lite, mainsheet block needed is Harken H2651.

H2733

$150.80

pivoting shackle for mainsheet block. Control tangs for attaching traveler blocks or lines

H2754

$183.05

Traveler car balls

- use to rebuild older-style Harken (loose ball) traveler car.

H177

$12.85

Traveler profile template

- reduce the height of your transom by removing the wood over the tiller hole. Traveler track will bend to this curve during installation

GG300

$5.00

MISCELLANEOUS

Compass Use to read the shifts. Non-racers can use for conventional navigation